In-Line Viscosity Measurement: How to integrate a viscometer into your continuous flow process?

Viscosity variations can affect product consistency and process performance. Detecting these changes during production gives manufacturers the information they need to adjust their process before deviations lead to off-specification material.

An in-line viscometer measures viscosity directly in the circulating product, under actual process conditions. It provides continuous information without requiring an external sample-conditioning system.

With the SOFRASER MIVI, this approach can be adapted to different pipe layouts, from direct insertion in the main line to installation in a dedicated flow cell.

What Is In-Line Viscosity Measurement? 

An in-line viscometer places its sensing element in direct contact with the process fluid.

The SOFRASER MIVI uses an active vibrating element immersed in the product, while the sensor body remains outside the pipe or measuring chamber. This allows viscosity changes to be monitored continuously at process temperature.

The measurement can support quality monitoring, operator decisions and automated process adjustments. Its value depends on selecting a measurement point that reflects the product circulating through the line.

Why Measure Viscosity Directly in the Process? 

Manual sampling provides information at specific intervals. Between samples, viscosity may change as temperature, composition or production conditions evolve.

Continuous in-line measurement helps production teams follow these changes as they occur.

Detect Process Variations Earlier: A continuous viscosity signal can reveal unexpected changes during production. Operators can investigate deviations sooner and, where the control system allows, adjust process parameters. 

Improve Production Repeatability: Monitoring viscosity against a validated operating range helps manufacturers maintain more consistent conditions from one production run to another. 

Support Automated Control: Viscosity data can be integrated into process automation systems to support adjustments such as dosing or dilution, depending on the application and control strategy. 

Reduce Dependence on Manual Sampling: In-line monitoring provides continuous process information between laboratory checks. Laboratory testing can remain necessary for final quality validation or measurements performed under standardised conditions. 

By helping teams detect deviations early and maintain more consistent process conditions, in-line viscosity measurement makes it possible to reduce non-conforming production, limit waste, and avoid the unnecessary consumption of raw materials.

Two Ways to Install an In-Line MIVI 

The most suitable mounting configuration depends on pipe diameter, available space and fluid circulation. MIVI sensors can operate in any position, providing flexibility when integrating the instrument into an existing process layout. 

1. Direct Insertion in a Process Pipe 

A recommended MIVI installation uses a proprietary mounting flange welded onto a pipe angle. The active element extends into the product stream, while the sensor body remains accessible outside the pipe.

A typical configuration uses a 2- or 3-inch pipe angle. The installation can also be adapted to very large pipes, including diameters of 20 inches or more, using a mini-immersion tube or straight-line mounting on a flanged nozzle.

Direct pipe mounting is particularly suitable when:

  • the line provides continuous, representative product circulation;
  • the sensing element can remain fully immersed;
  • viscosity needs to be monitored at actual process temperature;
  • the pipe geometry allows sufficient clearance around the active element;
  • access is available for installation and maintenance.

This configuration offers compact integration and avoids the need for an external sampling circuit.

Depending on application requirements, connections such as Tri-Clamp or Varivent® can also be considered.

2. Installation on a Flow Cell 

Direct insertion may be impractical when the main pipe is too small to accommodate the sensor.

For lines below ¾ inch, SOFRASER offers a dedicated measuring chamber, or flow cell, in which the MIVI can be installed. The standard chamber includes two inlet ports and one outlet port with ½-inch BSPT connections. Port sizes of ¼ inch or ¾ inch, as well as other thread types, are available on request. 

The flow cell may be integrated:

  • directly into the production line;
  • into a recirculation circuit;
  • into a bypass carrying a representative portion of the process fluid.

The MIVI still measures the product directly under process conditions. A bypass installation therefore requires careful consideration of circulation, temperature and transport delay to ensure that the measurement reflects the main stream.

InstallationWhen to consider it 
Direct pipe mounting The main pipe can accommodate the sensing element Immersion, cleaning and representative flow 
Flow cell in the production line Direct insertion is impractical on a small pipe Chamber integration and fluid circulation 
Flow cell on a recirculation circuit or bypass The process layout requires a separate measurement location Product renewal, temperature and transport delay 

Choosing the Right Measurement Point 

A suitable instrument needs a suitable installation point.

The sensing element must remain exposed to representative product. Air pockets, deposits, insufficient circulation or strong local disturbances can reduce the usefulness of the measurement.

Before selecting a location, consider:

  • pipe diameter, orientation and available mounting space;
  • minimum and maximum flow conditions;
  • whether the pipe remains full during measurement;
  • the risk of air bubbles, deposits or stagnant product;
  • temperature conditions at the measurement point;
  • clearance around the sensing element;
  • access for cleaning and maintenance.

For a flow cell on a bypass, the circuit must continuously renew the measured product. A poorly circulated loop may respond too slowly or expose the sensor to conditions that differ from those in the main line.

Managing Turbulence with Flow Damper Technology 

High flow rates can create turbulence around the sensing element. Depending on the fluid and installation geometry, these conditions may affect measurement stability.

SOFRASER’s Flow Damper acts as an embedded flow cell around the active measuring area. It channels the fluid and keeps flow lines more parallel to the vibrating element, helping stabilize the local measurement environment.

Its use should be assessed according to the product, flow conditions and mounting configuration. It is an application-dependent option, rather than a systematic requirement for every in-line installation.

Measure at Process Temperature or at a Reference Temperature?

In-line measurement follows viscosity under actual process conditions. Since viscosity depends on temperature, a change in the measured value may reflect a temperature variation, a composition change or both.

Temperature must therefore be considered when interpreting the signal and defining control limits.

If the objective is to analyse an extracted, conditioned sample at a defined reference temperature, an on-line analyzer may be more appropriate. The choice depends on the result required: continuous information for process control or viscosity analysis under controlled reference conditions.

What Information Is Needed to Select an Installation? 

To evaluate an in-line MIVI configuration, SOFRASER experts need a clear picture of the application: 

  • product composition and expected viscosity range;
  • normal and maximum temperature and pressure;
  • pipe diameter and layout;
  • flow rate and fluid velocity;
  • potential deposits, bubbles or cleaning constraints;
  • connection and wetted-material requirements;
  • hygienic requirements or hazardous-area classification;
  • available installation and maintenance space;
  • measurement objective and intended control strategy.

These details help determine whether direct insertion, a flow cell or an additional Flow Damper is appropriate.

In-Line Solutions for Different Applications 

Beyond the versatile MIVI, SOFRASER’s in-line range includes dedicated solutions: SOFine for coating applications, SOFlux for extrusion, SOFuel for fuel viscosity control and SOFeat for downhole applications. Selection depends on the process and operating requirements. 

Find the Right In-Line Configuration for Your Process 

In-line viscosity measurement provides continuous information where production decisions are made: directly in the process fluid.

With direct pipe mounting and flow-cell configurations, the SOFRASER MIVI can be integrated into different line layouts. Selecting the right measurement point and mounting arrangement helps turn the viscosity signal into useful information for process monitoring and control.

Stay connected with SOFRASER

Follow us on LinkedIn and subscribe to our YouTube channel to discover our latest news, tips, and expertise in viscosity measurement.

In-line

If you have any questions, please fill in the form.